Derracudas zermatt 20vt,6spd, 351awhp - July 4th drive vid

PhunkFX · Post by **PhunkFX** » Sat May 09, 2009 12:22 pm

I have been a long time reader of this thread, and I must say... this is all so amazing, you are seriously patient and talented!

Derek and 4000/Coupe GT folks... you remember this lip (chip spoiler)?

You guys ever think of finding one for your car? [/img]

derracuda · Post by **derracuda** » Sat May 09, 2009 12:43 pm

i've been trying to get in touch with someone who can make us CF copies of that chin spoiler. everyone flakes out. so, if anyone knows a reputable CF company or guy in a shed, lemme know!

PxTx · Post by **PxTx** » Sat May 09, 2009 2:27 pm

I would be fine with a glass copy. Unless it's a full on race application, I think CF is gaudy.

derracuda · Post by **derracuda** » Sat May 09, 2009 2:34 pm

i don't think real CF is gaudy... i think faux CF is stupid. you can't have a raw finish FG, it has to be body color... so, CF sounds good to me, and i think it will look nice with the zermatt color tone wise. the other thing i want to make with CF is replicate the Blau trunk spoiler extension i have... just some nice touches

PhunkFX · Post by **PhunkFX** » Sat May 09, 2009 2:37 pm

I have one in my attic

Derek... amazing work! I am thoroughly happy for you and the outcome of your hard work! An inspiration for sure!

derracuda · Post by **derracuda** » Sat May 09, 2009 2:41 pm

i'm pretty sure i remember pics of that car when i first got into audi's.. searching AF registry and all that.

derracuda · Post by **derracuda** » Sat May 09, 2009 3:59 pm

huh, i just found this..

http://en.wikipedia.org/wiki/Zermatt

cool!

my2000apb · Post by **my2000apb** » Sat May 09, 2009 5:14 pm

sell me that 3b wire cover!!

Quattro Krant · Post by **Quattro Krant** » Sat May 09, 2009 8:11 pm

PhunkFX wrote:I have been a long time reader of this thread, and I must say... this is all so amazing, you are seriously patient and talented!

Derek and 4000/Coupe GT folks... you remember this lip (chip spoiler)?

You guys ever think of finding one for your car? [/img]

There is a gent with a Ur-Q, Phil, with a modded MK2 VW spoiler that looks FANTASTIC on it, looks factory.

naudi80quattro · Post by **naudi80quattro** » Sat May 09, 2009 11:42 pm

im pretty sure spike_rally could do fiberglass copies he was gonna make copies of the s2 rear bumper i had. also those mk2/mk3 spoiler can be widely used on different cars and defiitley look good

85oceanic · Post by **85oceanic** » Mon May 11, 2009 3:01 pm

Personally I think a CF one would be bad ass.... i hope some one annies up and does it. :roll:

cuatrokoop · Post by **cuatrokoop** » Mon May 11, 2009 3:34 pm

Ante up, as in a gambling term...

Post by **Hank** » Mon May 11, 2009 5:18 pm

Does anybody have one that could be used to pull the mold?

85oceanic · Post by **85oceanic** » Tue May 12, 2009 1:45 pm

woops my bad ... Ante up... :roll:

Clouse · Post by **Clouse** » Tue May 12, 2009 4:27 pm

ShavedQuattro wrote:Does anybody have one that could be used to pull the mold?

Ya. if anyone has one I could probably make a couple here at school. Though it'd have to be quick since I graduate June 13th. And I couldn't guarantee a PERFECT finish... but I can always try.

derracuda · Post by **derracuda** » Thu May 21, 2009 8:16 pm

alrighty.... time for a new exhaust

i've been planning this one out for a long time now, and collected all the pieces i needed.... except a second spool of SS mig wire

i made huge strides on my exhaust today, yesterday, and back on monday. i started this back in february, but have been MIA for a while with traveling and work... but alas, it is *almost* complete. i have about 30 minutes more welding/finalizing and then she can be bolted up in place for good.

the idea of this exhaust is to use different pipe sizes for #1. flow, #2. hopefully confuse the exhaust pulses into not resonating like a big jerk so that i can enjoy the lower cruising rpms with these URQ gears. so far, it looks like a winner.... i ran it with the one remaining joint to be welded up butted up tight, and there's plenty of noise at the tips, but inside the car is pretty quiet through the rev range.... putting a load on it will tell for sure, but it's definitely quieter inside than my old 20vt was with a straight 3" pipe, center resonator, and rear muffler....

this one consists of... ready for it? downpipe - 3" flexpipe - 3" resonator - splitting down into dual 2.5" under the middle of the car for clearance and dividing the pulses - then into dual 2.75" pipes with same size resonators - into single 3" up and over the rear axle - divided again into dual 2.75" through two more resonators - one side exits in a 3", the other a 2.75" - they merge and then split at the very end for the tips... which are B6 S4 tips i got of an exhaust i won on ebay for $20

i wanted the vacuum operated valves from the ends, but they were too small for my likes... so i said screw it and went all out to try this experimental exhaust.

i made a video, but unfortunately the pipe slid back enough to reveal the "leak" that makes it sound like a tractor again. i'll be welding this up as soon as i can and get a final product sound clip for ya'll 8)

and now, for a pic buffet that i've been waiting so long to put up

so this is how it starts... a pile of pipes and resonators..

dual 2.5" welded together with SS angle brackets to space them evenly..

i made all the hangers out of 1/4" SS rod...

sometimes ya gotta make due with whatcha got

added the second routing in here...

mid section...

tips 8)

video is uploading at the moment, i'll update in a few when it's ready :

Video

http://www.facebook.com/video/?id=68044 ... 2697728508

pilihp2 · Post by **pilihp2** » Thu May 21, 2009 8:24 pm

thats alot of freakin pipe...

way awesome..

derracuda · Post by **derracuda** » Thu May 21, 2009 8:30 pm

you're telling me man.. i think i have like 8th degree welders burn on my forearms

Post by **Hank** » Thu May 21, 2009 8:50 pm

Looks Derek!! I like the 2.5" idea!!

Mine will show up here soon too!!

quattro87 · Post by **quattro87** » Thu May 21, 2009 8:51 pm

Nice Derek!! I like it and I'll venture to guess that it does pretty well in both performance and sound quality. I'm still wondering if you were showing off the exhaust or the nice no rust near perfect underside of the car. Impressive.

Val · Post by **Val** » Thu May 21, 2009 11:45 pm

Can video be seen w/o facebook login?
Anyway, looks great :thumbsup:

my2000apb · Post by **my2000apb** » Fri May 22, 2009 5:54 am

yeah wtf facebook sucks, i jsut wanna see the vid!!!

looking kick ass derek, id drive my car open mani across the great usa to get one of those sexy exhausts

derracuda · Post by **derracuda** » Fri May 22, 2009 5:58 am

huh... i posted videos from the beach off facebook before when i got stuck in my A6...

facebook video's come out much clearer than youtube quality wise. that's why i used it.

plus, youtube gives me fits on large file videos, and this one is 80mb.

WAUG0806 · Post by **WAUG0806** » Fri May 22, 2009 6:14 am

ShavedQuattro wrote:Does anybody have one that could be used to pull the mold?

moi

cuatrokoop · Post by **cuatrokoop** » Fri May 22, 2009 7:39 am

derracuda wrote:huh... i posted videos from the beach off facebook before when i got stuck in my A6...

facebook video's come out much clearer than youtube quality wise. that's why i used it.

plus, youtube gives me fits on large file videos, and this one is 80mb.

Need to change the permissions so everyone can view it...